b7d6ec83 simplewallet: add (out of sync) or (no daemon) markers in the prompt (moneromooo-monero)
fa23a500 wallet2: add a is_synced function (moneromooo-monero)
f1307bbd node_rpc_proxy: add a proxy for target height (moneromooo-monero)
Asks user for all the data required to merge secret keys from multisig wallets into one master wallet, which then gets full control of the multisig wallet. The resulting wallet will be the same as any other regular wallet.
It sweeps all outputs below the given threshold
This is available via the existing sweep_all RPC, by setting
amount_threshold the desired amount (in atomic units)
With the change from the original transfer method to the new
algorithm, payments to the same destination were merged. It
seemed like a good idea, optimizing space. However, it is a
useful tool for people who want to split large outputs into
several smaller ones (ie, service providers making frequent
payments, and who do not like a large chunk of their balance
being locked for 10 blocks after each payment).
Default to off, which is a change from the previous behavior.
When a single input is enough to satisfy a transfer, the code would
previously try to add a second input, to match the "canonical" makeup
of a transaction with two inputs and two outputs. This would cause
wallets to slowly merge outputs till all the monero ends up in a
single output, which causes trouble when making two transactions
one after the other, since change is locked for 10 blocks, and an
increasing portion of the remaining balance would end up locked on
each transaction.
There are two new settings (min-output-count and min-output-value)
which can control when to stop adding such unneeded second outputs.
The idea is that small "dust" outputs will still get added, but
larger ones will not.
Enable with, eg:
set min-output-count 10
set min-output-value 30
to avoid using an unneeded second output of 30 monero or more, if
there would be less than 10 such outputs left.
This does not invalidate any other reason why such outputs would
be used (ie, when they're really needed to satisfy a transfer, or
when randomly picked in the normal course of selection). This may
be improved in the future.
This replaces the epee and data_loggers logging systems with
a single one, and also adds filename:line and explicit severity
levels. Categories may be defined, and logging severity set
by category (or set of categories). epee style 0-4 log level
maps to a sensible severity configuration. Log files now also
rotate when reaching 100 MB.
To select which logs to output, use the MONERO_LOGS environment
variable, with a comma separated list of categories (globs are
supported), with their requested severity level after a colon.
If a log matches more than one such setting, the last one in
the configuration string applies. A few examples:
This one is (mostly) silent, only outputting fatal errors:
MONERO_LOGS=*:FATAL
This one is very verbose:
MONERO_LOGS=*:TRACE
This one is totally silent (logwise):
MONERO_LOGS=""
This one outputs all errors and warnings, except for the
"verify" category, which prints just fatal errors (the verify
category is used for logs about incoming transactions and
blocks, and it is expected that some/many will fail to verify,
hence we don't want the spam):
MONERO_LOGS=*:WARNING,verify:FATAL
Log levels are, in decreasing order of priority:
FATAL, ERROR, WARNING, INFO, DEBUG, TRACE
Subcategories may be added using prefixes and globs. This
example will output net.p2p logs at the TRACE level, but all
other net* logs only at INFO:
MONERO_LOGS=*:ERROR,net*:INFO,net.p2p:TRACE
Logs which are intended for the user (which Monero was using
a lot through epee, but really isn't a nice way to go things)
should use the "global" category. There are a few helper macros
for using this category, eg: MGINFO("this shows up by default")
or MGINFO_RED("this is red"), to try to keep a similar look
and feel for now.
Existing epee log macros still exist, and map to the new log
levels, but since they're used as a "user facing" UI element
as much as a logging system, they often don't map well to log
severities (ie, a log level 0 log may be an error, or may be
something we want the user to see, such as an important info).
In those cases, I tried to use the new macros. In other cases,
I left the existing macros in. When modifying logs, it is
probably best to switch to the new macros with explicit levels.
The --log-level options and set_log commands now also accept
category settings, in addition to the epee style log levels.
c2135082 simplewallet: add a show_transfer <txid> command (moneromooo-monero)
19c4041d wallet_rpc_server: new RPC call to get a transfer by txid (moneromooo-monero)
When passing around unsigned and signed transactions, outputs
and key images are passed along (outputs are passed along unsigned
transactions from the hot wallet to the cold wallet, key images
are passed along with signed transations from the cold wallet
to the hot wallet), to allow more user friendly syncing between
hot and cold wallets.
The intended use is to export outputs from a hot wallet, which
can scan incoming transfers from the network, and import them
in the cold wallet, which can't. The cold wallet can then compute
key images for those outputs, which can then be exported with
export_key_images, etc.
714ee99 Fix description for locked_transfer (Oyvind Kvanes)
71538f3 Rename to lockblocks and add max value (Oyvind Kvanes)
68ac060 Fix locked_transfer (Oyvind Kvanes)
7d020bd Add locked_transfer (Oyvind Kvanes)
d5f918a Revert transfer_main in simplewallet (Oyvind Kvanes)
3451963 Add motifications to test out locked_transfer (Oyvind Kvanes)
e5e6d88 Add more information to transaction in wallet (Oyvind Kvanes)
9b8a062 Make a small test change (Oyvind Kvanes)
