When scanning the txpool without having first updated the
blockchain, the tx would be seen as neither in the txpool
nor the chain, and removed, so it'd only reappear once the
chain is refreshed, and the tx seen in a block.
It sweeps all outputs below the given threshold
This is available via the existing sweep_all RPC, by setting
amount_threshold the desired amount (in atomic units)
With the change from the original transfer method to the new
algorithm, payments to the same destination were merged. It
seemed like a good idea, optimizing space. However, it is a
useful tool for people who want to split large outputs into
several smaller ones (ie, service providers making frequent
payments, and who do not like a large chunk of their balance
being locked for 10 blocks after each payment).
Default to off, which is a change from the previous behavior.
When a single input is enough to satisfy a transfer, the code would
previously try to add a second input, to match the "canonical" makeup
of a transaction with two inputs and two outputs. This would cause
wallets to slowly merge outputs till all the monero ends up in a
single output, which causes trouble when making two transactions
one after the other, since change is locked for 10 blocks, and an
increasing portion of the remaining balance would end up locked on
each transaction.
There are two new settings (min-output-count and min-output-value)
which can control when to stop adding such unneeded second outputs.
The idea is that small "dust" outputs will still get added, but
larger ones will not.
Enable with, eg:
set min-output-count 10
set min-output-value 30
to avoid using an unneeded second output of 30 monero or more, if
there would be less than 10 such outputs left.
This does not invalidate any other reason why such outputs would
be used (ie, when they're really needed to satisfy a transfer, or
when randomly picked in the normal course of selection). This may
be improved in the future.
Asking for a full histogram from a remote node (since it's
untrusted) is pretty slow, and spams the remote node, so
we replace it by only adding a second input if we have rct
ones, which are for all intents and purposes always mixable.
Minimum mixin 4 and enforced ringct is moved from v5 to v6.
v5 is now used for an increased minimum block size (from 60000
to 300000) to cater for larger typical/minimum transaction size.
The fee algorithm is also changed to decrease the base per kB
fee, and add a cheap tier for those transactions which we do
not care if they get delayed (or even included in a block).
c02e1cb9 Updates to epee HTTP client code - http_simple_client now uses std::chrono for timeouts - http_simple_client accepts timeouts per connect / invoke call - shortened names of epee http invoke functions - invoke command functions only take relative path, connection is not automatically performed (Lee Clagett)
- http_simple_client now uses std::chrono for timeouts
- http_simple_client accepts timeouts per connect / invoke call
- shortened names of epee http invoke functions
- invoke command functions only take relative path, connection
is not automatically performed
This avoids indirectly leaking the real output to the daemon,
and is faster.
This will still happen for more complex cases, especially
when cancelling a tx and "re-rolling" it.
This replaces the epee and data_loggers logging systems with
a single one, and also adds filename:line and explicit severity
levels. Categories may be defined, and logging severity set
by category (or set of categories). epee style 0-4 log level
maps to a sensible severity configuration. Log files now also
rotate when reaching 100 MB.
To select which logs to output, use the MONERO_LOGS environment
variable, with a comma separated list of categories (globs are
supported), with their requested severity level after a colon.
If a log matches more than one such setting, the last one in
the configuration string applies. A few examples:
This one is (mostly) silent, only outputting fatal errors:
MONERO_LOGS=*:FATAL
This one is very verbose:
MONERO_LOGS=*:TRACE
This one is totally silent (logwise):
MONERO_LOGS=""
This one outputs all errors and warnings, except for the
"verify" category, which prints just fatal errors (the verify
category is used for logs about incoming transactions and
blocks, and it is expected that some/many will fail to verify,
hence we don't want the spam):
MONERO_LOGS=*:WARNING,verify:FATAL
Log levels are, in decreasing order of priority:
FATAL, ERROR, WARNING, INFO, DEBUG, TRACE
Subcategories may be added using prefixes and globs. This
example will output net.p2p logs at the TRACE level, but all
other net* logs only at INFO:
MONERO_LOGS=*:ERROR,net*:INFO,net.p2p:TRACE
Logs which are intended for the user (which Monero was using
a lot through epee, but really isn't a nice way to go things)
should use the "global" category. There are a few helper macros
for using this category, eg: MGINFO("this shows up by default")
or MGINFO_RED("this is red"), to try to keep a similar look
and feel for now.
Existing epee log macros still exist, and map to the new log
levels, but since they're used as a "user facing" UI element
as much as a logging system, they often don't map well to log
severities (ie, a log level 0 log may be an error, or may be
something we want the user to see, such as an important info).
In those cases, I tried to use the new macros. In other cases,
I left the existing macros in. When modifying logs, it is
probably best to switch to the new macros with explicit levels.
The --log-level options and set_log commands now also accept
category settings, in addition to the epee style log levels.
If we'd make a rct tx with just one input, we try to add
a second one to match the 2/2 ideal. This means more txes
use that template (and are thus using a larger anonymity
set), and it coalesces outputs "for free". We use the
smallest amount outputs in priority for this, so we can
"clean" the wallet at the same time.
A bug in cold signing caused a spurious pubkey to be included
in transactions, so we need to ensure we use the correct one
when sending outputs from one of those.
5783dd8c tests: add unit tests for uri parsing (moneromooo-monero)
82ba2108 wallet: add API and RPC to create/parse monero: URIs (moneromooo-monero)
d9001b43 epee: add functions to convert from URL format (ie, %XX values) (moneromooo-monero)
Daemon RPC version is now composed of a major and minor number,
so that incompatible changes bump the major version, while
compatible changes can still bump the minor version without
causing clients to unnecessarily complain.
6d76072 simplewallet: remove double confirmation when submitting signed tx (moneromooo-monero)
92dea04 wallet2: fix wrong change being recorded for cold signed txes (moneromooo-monero)
When passing around unsigned and signed transactions, outputs
and key images are passed along (outputs are passed along unsigned
transactions from the hot wallet to the cold wallet, key images
are passed along with signed transations from the cold wallet
to the hot wallet), to allow more user friendly syncing between
hot and cold wallets.
View wallets do not have the spend secret key, and are thus
unable to derive key images for incoming outputs. Moreover,
a previous patch set key images to zero as a means to mark
an output as having an unknown key image, so they could be
filled in when importing key images at a later time. That
later patch caused spurious collisions. We now use public
keys to detect duplicate outputs. Public keys obtained from
the blockchain are checked to be identical to the ones
derived locally, so can't be spoofed.
m_amount_out was sometimes getting initialized with the sum of
an transaction's outputs, and sometimes with the sum of outputs
that were not change. This caused confusion and bugs. We now
always set it to the sum of outputs. This reverts an earlier
fix for bad amounts as this used the other semantics. The wallet
data should be converted automatically in a percentage of cases
that I'm hesitant to estimate. In any case, restoring from seed
or keys or rebuilding the cache will get it right.
Compute derivation only once per tx, instead of once per output. Approx 33% faster while using 75% as much CPU on my machine. Note old functions in cryptonote_core (lookup_acc_outs and is_out_to_acc) are still used by tests.
The intended use is to export outputs from a hot wallet, which
can scan incoming transfers from the network, and import them
in the cold wallet, which can't. The cold wallet can then compute
key images for those outputs, which can then be exported with
export_key_images, etc.
Re-creating the transaction on the cold wallet was not splitting
the change, causing the transaction to be rejected by the network.
This worked on testnet since amounts do not have to be split.
Also add selected_transfers, which can now be saved since they're
size_t rather than iterators. This allows the view wallet to
properly set the sent outputs as spent and update balance.
Bump transfer file version numbers to match.
This was still using the old transaction creation algorithm,
coupled with a deterministic output selection scheme, which
made it ill suited to the job, since it'd loop indefinitely
in case the fee increased between the test tx and adding the
fee.
